Microchip Technology dsPICDEM MCLV-2 Manual de usuario descargar pdf (Pagina 24)

16-bit Embedded Control Solutions

Development Tools for Motor Control Applications

Microchip offers a number of hardware tools to assist

in the development of motor control applications. These

tools work with Microchip’s MPLAB IDE and an in-circuit

debugger to download and debug application software. Our

systems make it easy to customize the software from our

application notes and demo code to run different motors.

dsPICDEM™ MCSM Stepper Motor: Motor Control

Development Board/Kit (DM330022)/(DV330021)

This development board is intended for

low-voltage (up to 80 volts at 3 amps)

2-phase uni-polar or bi-polar stepper

motor (4, 6 or 8 wire) applications. It

provides a low-cost system for users

to evaluate and develop applications

using dsPIC33 motor control DSCs

via a Plug-In Module (PIM) or 28-pin

SOIC socket. A USB serial interface for

RTDM is provided. Feedback support

includes current and voltage. Demo software to run motors

in open-loop or closed-loop with full or variable micro-

stepping is provided. A DMCI/RTDM GUI for controlling

step commands, motor parameter input and operation

modes is included. The kit includes a stepper motor and a

24-volt power supply. MPLAB ICD 3 In-Circuit Debugger or

REAL ICE In-Circuit Emulator is required for programming or

debugging operations.

dsPICDEM MCLV-2 Development Board (DM330021-2)

This development board is intended

for low-voltage (up to 48 volts at 10

amps) BLDC sensored or sensorless

applications. It provides a low-cost

system for users to evaluate and

develop applications using dsPIC33F/E motor control DSCs

via a Plug-In Module (PIM) or 28-pin SOIC socket. With the

MCLV-2 either the internal, on chip op amps or the external

op amps on the MCLV-2 board can be used. Microchip

provides PIMs for using either the internal or external op

amps. The MCLV-2 is fully backwards compatible with the

original MCLV and all MC PIMs. Serial interfaces include:

RS-232C, CAN, LIN and USB (for RTDM). Feedback support

includes: Hall- Effect Sensors, Shaft Encoder, Back EMF

voltages and single or dual shunt resistors for current.

PICkit 3 Debug Express, MPLAB ICD 3 In-Circuit Debugger

or REAL ICE In-Circuit Emulator is required for programming

or debugging operations.

dsPICDEM MCHV-2 Development System (DM330023-2)

This development system is intended

for high-voltage (up to 400 volts at 6.5

amps) BLDC, PMSM and ACIM sensored

or sensorless applications. It provides a

low-cost Integrated Power Module (IPM)

based system for users to evaluate and

develop applications using dsPIC33F/E motor control

DSCs via a Plug-In Module (PIM) or a 28-pin SOIC socket.

With the MCHV-2 either the internal, on chip op amps or

the external op amps on the MCHV-2 board can be used.

Microchip provides PIMs for using either the internal

or external op amps. The MCHV-2 is fully backwards

compatible with the original MCHV and all MC PIMs.

Isolated serial interfaces include RS-232C and USB (for

RTDM). Feedback support includes: Hall-Effect Sensors,

Shaft Encoder, Back EMF voltages and single or dual

current shunt resistors. A PFC circuit is provided to meet

regulatory requirements. An isolated built-in debugger

(similar to a starter kit programmer/debugger) permits a

direct connection with a PC.

dsPIC33E Dual Motor Control Plug-In Module (PIM)

(MA33027)

This Dual Motor Control PIM

is designed to facilitate the

development of motor control applications using two

motors and one dsPIC33E Digital Signal Controller (DSC).

Two Microchip PIM based motor control development

boards can be used with this PIM to control two BLDC,

PMSM, ACIM or stepper motors. A flexible cable connects

the two boards together and routes all signals to the

appropriate pins on the dsPIC33E DSC. The configuration

of the cable and signals was carefully chosen to support

a wide range of dual motor configuration application

notes written for the dsPICDEM MCLV, MCHV and MCSM

development boards.

Motor Control Development Systems for

dsPIC30F

PICDEM MC LV Motor Control Development Board

(DM183021)

This development board is intended

for low-voltage (up to 48V at 2 amps),

Brushless DC (BLDC) sensored or

sensorless applications. It provides a

low-cost board for users to evaluate

and develop applications using Microchip’s 28-pin

PIC18FXX31 and dsPIC30F motor control devices. An

18-pin translator board (AC162078) is also available

and allows the PIC18F1330 to be installed on the board.

Feedback support includes Hall-Effect Sensors and Back

EMF voltages. MPLAB ICD 3 In-Circuit Debugger or REAL

ICE In-Circuit Emulator is required for programming or

debugging operations.

Motors

You can provide your own motor or purchase one of the

motors used in our application notes and guaranteed to

run, right out of the box:

■ AC300024: 2-phase, 8-wire Stepper Motor

■ AC300020: 24V BLDC Motor

■ AC300022: 24V BLDC Motor with Shaft Encoder

■ AC300023: 220V, AC Induction Motor

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 35 36

Comentarios a estos manuales

Sin comentarios

Microchip Technology dsPICDEM MCLV-2 Manual de usuario Pagina 24

Comentarios a estos manuales

Relacionado con productos y manuales para Barebones Pc / Estación De Trabajo Microchip Technology dsPICDEM MCLV-2